We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

ACE 2 DCC Controller by SIG Natrak: Setup Steps and Key Functions

Learn how to set up the ACE 2 DCC controller by SIG Natrak, from wiring and address programming to throttle functions and common troubleshooting tips.

Updated November 2026

The ACE 2 DCC controller by SIG Natrak is a handheld throttle designed to run locomotives on a Digital Command Control layout. In this guide, you will learn how to connect the controller, assign a locomotive address, run trains and use the functions that matter most day to day. The steps below apply to the general workflow for this type of system, so always check the official SIG Natrak documentation for model-specific details.

Before You Start: What You Need

Gather the basics before you touch the layout. A working DCC command station, a regulated power supply, and track or a programming track section are the foundation. Make sure your locomotives are DCC-equipped or have a decoder installed.

Shopping for one? See our guide: 4 Best HO Scale DCC Controllers for Model Railroaders (2026).

  • The ACE 2 handheld controller and its connecting cable
  • A compatible DCC command station and power supply
  • Locomotives with DCC decoders (factory-installed or added)
  • A small screwdriver for any terminal connections
  • A multimeter for checking track voltage and continuity

How to Connect and Power Up the ACE 2

Connect the controller to the command station using the supplied cable and the correct jack. Turn on the power supply first, then the command station, and confirm the controller displays its startup screen. If the display stays blank, check the connector seating before assuming a fault.

  1. Power off the command station before plugging in the controller.
  2. Seat the cable firmly at both ends.
  3. Power on the supply, then the command station.
  4. Wait for the controller to finish its startup sequence.

Programming a Locomotive Address

Each locomotive needs a unique address so the command station knows which engine to control. Place the locomotive on the programming track, then use the programming menu on the ACE 2 to write a short address (typically 1 to 127) to the decoder. Once the address is saved, move the engine to the main line and confirm it responds to throttle commands.

Checking the Address

Select the address from the controller and run the locomotive at a low speed step. If it does not respond, recheck the address and confirm the decoder is seated correctly.

Running Trains and Using Key Functions

Once a locomotive is selected, the throttle controls speed and direction, while the function buttons control features such as lights, sound and horn. Increase speed gradually, and bring the engine to a full stop before reversing direction. Many owners find it helpful to build a short list of addresses for frequently run locomotives so they can switch engines quickly.

Control Typical Use
Speed dial or throttle Sets locomotive speed step
Direction control Reverses the locomotive
F0 Headlight or front light
F1 and higher Sound, horn, bell and decoder-specific functions

Function assignments vary by decoder, so consult the decoder documentation for exact numbers. For a broader look at control options, see Which DCC Controller Is Best? How to Choose the Right One for Your Layout.

Common Mistakes and Troubleshooting Tips

  • Plugging the controller in while the command station is powered can cause connection problems, so power down first.
  • Duplicate addresses cause two engines to respond to one throttle. Give every locomotive its own number.
  • Dirty track or poor wheel contact can mimic a controller fault. Clean the rails and wheels before troubleshooting further.
  • Overloaded power supplies can cause intermittent behavior. Confirm the supply meets the command station’s stated requirements.

For a broader set of solutions to common DCC problems, see Hornby Dcc Controller Problems: Causes and Fixes That Work (2026).

A reliable multimeter helps you verify track voltage before blaming the controller. Look for a model with a continuity function, since it speeds up wiring checks.

View on Amazon

A small set of precision screwdrivers makes it easier to work on decoder and terminal connections without stripping screw heads.

View on Amazon

FAQ

Can I use the ACE 2 with any DCC system?

The ACE 2 is designed for DCC operation, but compatibility depends on the command station and its protocol support. Check the manufacturer’s compatibility information before connecting it to a different system.

How do I reset a locomotive address?

Return the locomotive to the programming track and write a new address using the programming menu. The new value replaces the old one.

Why does my locomotive respond slowly?

Slow response is often caused by a low speed step setting, poor track contact or a decoder with incorrect speed table values. Clean the track and review the decoder’s speed settings.

Conclusion

With the ACE 2 connected, addressed and tested, you can run locomotives with confidence and use the function buttons to add realism. Keep addresses organized and clean your track regularly to avoid most common problems. For official specifications, wiring diagrams and model-specific settings, consult the SIG Natrak manual.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our model railroading guides, checking product details against manufacturer specifications and owner feedback.

About the author

Caleb Morgan
Caleb Morgan

Caleb Morgan writes reviews and buying guides for Railroading Online.